
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki) The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping. With a compact and light weight body, performances are upgraded compared to the previous model LG-916. (LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
- Upgraded performances (compared to the previous model LG-916) Detection distance : up to 40 mm Response speed : up to 40 m/s
- Easy to adjust a position by red visible light and operation indicator
- Possible to detect from lower speed almost 0 r/min
- A unified structure of light source, receiver and amplifier (weight : approx. 150 g)
- Provided a drop-proof connector as standard
Compatible Tachometers: Ono Sokki TM-2110, TM-2120, TM-2130, TM-2140, TM-3100 Series, SE-1620, and CT-6520B
Old Tachometer Sensor Compatibility Chart
TACHOMETER SENSOR |
TACHOMETER |
||||||
CT-6520/6520B |
SE-1520/1620 |
SE-1400 |
FT-1500 |
TM-2100 |
GE-1100 |
||
CP-044 | Clamp-On Fuel Injection Line | Note 1 | X | ||||
CP-1060 | Clamp-On Fuel Injection Line | Note 1 | X | ||||
CP-1064 | Clamp-On Fuel Injection Line | Note 1 | X | ||||
FT-0501 | Magnetic Flux Leakage Detector | X | |||||
IP-292 | Inductive Clamp-On (Primary) | X | X | Note 2 | |||
IP-296 | Inductive Clamp-On (Secondary) | X | Note 2 | ||||
IP-2800 | Inductive Suction Cup (Primary) | X | |||||
IP-3000 | Inductive Clamp-On (Primary) | X | X | Note 2 | |||
LG-916 | Optical Tachometer Sensor | MX-800 Series | MX-700 Series | ||||
MP-910 | Magnetic Pickup | MX-000Series | MX-500 Series | ||||
MP-981 | Hall-Effect Magnetic Pickup | MX-800 Series | MX-700 Series | ||||
MP-910 | Magnetic Pickup | MX-000Series | MX-500 Series | ||||
OM-200 | Magnetic Flux Detector | MX-000 Series | Note 3 | Note 2 | |||
VP-201 | Vibration Sensing Tach Sensor | X | Note 3 | X | |||
VP-202 | Vibration Sensing Tach Sensor | X | |||||
Measurement Microphone | Note 4 | ||||||
Vibration Transducer | Note 4 |
KEY
Blank => sensor is not compatible with tachometer Model # => sensor is compatible with tachometer using the specified cable model #
X => sensor is compatible with tachometer using integral cable
Note => sensor may be used with this tachometer with certain restrictions (see below)
Note 1: CP-Series Clamp-On sensors may be used with FT-1500 tachometer for diesel engine rpm measurements. In-line charge amplifier is required. Please contact us for details.
Note 2: IP-Series Inductive sensors may be used with the FT-1500 tachometer for rpm measurements on DC motors. Please contact us to discuss your application.
Note 3: A special modification is available for the SE-1520 tachometer that will permit the